Electro-Hydraulics Training system

Electro-Hydraulics Training system

Electro-Hydraulics Training system

Lab Catalog Supply Code: NPC-18-06-18-0034

Electro-Hydraulics Training system
The system Should Cover the Following training contents:
Physical principles of electrical systems and pneumatics
Function and use of electro-pneumatic components
Recognizing and drawing of electro-pneumatic symbols
Representation of motion sequences and operating status
Drawing of pneumatic and electrical circuit diagrams
Direct and indirect manual controls
Direct and indirect position-dependent controls
Logical AND/OR function of switch-on signals
Representing motion sequences and switching states
Constructing control systems using relays
Electrical latching circuits
Application and function of 3/2 and 5/2-way solenoid valves
Analyzing circuits
Function and application of limit switches
End-position monitoring using electronic proximity sensors
The system Should Cover the Following training contents:
Function of electrical pushbuttons switches and limit switches
Function and use of hydraulic solenoid valves
Design and mode of operation of a relay
Recognizing and reading of electrical and hydraulic diagrams
Design, construction and operation of basic circuits
Selecting solenoid valves according to the technical control requirements
Using and designing of basic logic functions
Direct and indirect control of actuators
Explaining and designing an electric latching circuit
Electrically a locking of signals in a relay control system
Manual and automatic operation
Interlocking circuits
Rapid traverse circuits
Using of a pressure switch
Fault finding in electro-hydraulic control system  
Minimum Technical Specifications Required  (like or better than):
Student Vertical Workbench for Hydraulic and Electro Hydraulic  
Drawers Unit with a lock-key
Aluminum profile plate: 1200 × 750 mm at least
Groove distance: 25mm for quick fix of aluminium profiles components  
Construction and easily setup the system according to the
circumstances
Mounting bar for fixing electric devices Aluminium profile plate
All Components Must be one Touch Clamp  
Hydraulic power unit pump 1.5 kw at least with flow rate:3 l/min and Tank: 25 L
Overload protector unit with Thermal relay, LED display  
Transparent Flow Measurer Unit :2L with flow limit sensor and hand valve  
Stainless steel Oil tray with press punching hole  
Hydraulic Oil (40 L)
Transparent double-acting cylinder, Stroke: 150 mm  
Double-acting cylinder, Cylinder stroke: 200 mm  
Weight 9kg coated  
Hydraulic motor with tow way directional Operation, RPM: 1950
2x Pressure relief valve (directly actuated)
2x One-way flow control  valve
Flow control valve (pressure compensative)
Check valve (1bar)
Pilot actuated check valve, Max Pressure: 120 bar  
3x Pressure gauge
2x Pressure gauge with distributor 4 port
2x T connector, Max Pressure: 120 bar
2x Hydraulic Hose 1500mm
4x Hydraulic Hose 1000mm
8x Hydraulic Hose 600mm
Hydraulic  hose hanger
Pressure remover
3/2-way single solenoid valve with LED Display, Max Pressure: 120 bar
4/2-way single solenoid valve with LED Display, Max Pressure: 120 bar
4/2-way double solenoid valve with LED Display, Max Pressure: 120 bar
4/3-way solenoid valve (PABT blocked), Max Pressure: 120 bar
4/3-way solenoid valve PT bypassed, Max Pressure: 120 bar
Power supply: DC 24V, 5A with Short-circuit and overload protection
Adjustable Pressure switch  
Push-button switch Unit including three Push-button
Lamp and buzzer unit
2x Relay Unit Three-fold, Operating time: >20 ms, Drop-off time: >20 ms
Digital Time relay Unit, Delay time: 1-99 sec
2x Electric  limit switch  (left)
2x Electric  limit switch  (right)
Inductive sensor N/O, switching distance: 5 mm
Capacitive sensor N/O, switching distance: 8 mm
Optical  sensor N/O, switching distance: 200 mm
•     4mm electric cable set
Electro-Hydraulics Training system Operation Manual, Lab Instructor Guide and Student Workbook. Electro-Hydraulics Training system for Educational Vocational, Didactic Technical Training Equipment Labs.

Add to Cart